Ubiquiti NANOBEAM NBE-5AC-19

104.00 with VAT

Ubiquiti NANOBEAM NBE-5AC-19



Ubiquiti NanoBeam-5AC-19 / NBE-5AC-19

Ubiquiti Networks launches the latest generation of airMAX CPE (Customer Premises Equipment), the NanoBeam ac. Using airMAX ac technology, the NBE 5AC-19 supports up to 450+ Mbps real TCP/IP throughput.

New RF-Design

The NanoBeam AC directs RF energy in a tighter beamwidth. With the focus in one direction, the NanoBeam AC blocks or spatially filters out noise, so noise immunity is improved. This feature is especially important in an area crowded with other RF signals of the same or similar frequency.

Integrated Design

The Ubiquiti Research and Development team combined the radio and antenna to create a more efficient and compact CPE. The NanoBeam 5AC-19 gets maximum gain out ofthe smallest footprint. Providing increased performance from its faster processor and innovative mechanical design at a low cost, the NanoBeam is extremely versatile andcost effective to deploy.

Compact and robust outdoor design

Very small visible footpint. Mechanical design provides complete weatherproof performance. Acitivity and signal strength LED’s provided for installers. Enhanced RF and Ethernet ESD/Surge protection enables prolonged operation in harshest environments. The NanoBeam AC is designed for mast or pole installation.

airMAX Technology

The next generation airMAX ac technology boosts the advantages of our proprietary TDMA protocol. Ubiquiti?s airMAX engine with custom IC dramatically improves TDMA latency and network scalability. The custom silicon provides hardware acceleration capabilities to the airMAX scheduler, to support the high data rates and dense modulation used in airMAX ac technology.

airMAX ac supports high data rates, which require dense modulation: 256QAM ? a significant increase from 64QAM, which is used in airMAX. With their use of proprietary airMAX ac technology, airMAX ac products supports up to 450+ Mbps real TCP/IP throughput ? up to triple the throughput of standard airMAX products.

Passive PoE

Using PoE technology allows to transmit data stream and power / energy through the enthernet cable which integrates the NanoBeam M5 AC to your network enviroment. There is no need to to install any extra wired power cord. A Gigabit 24V, 0.5A PoE Injector is included.

AirOS Software

AirOS is the intuitive, versatile, highly developed Ubiquiti firmware technology. It is exceptionally intuitive and was designed to require no training operate. Behind the user webinterface is a powerful firmware architecture which enables hi-performance networking. Additionally, the AirControl application allows operators to centrally manage 100’s of devices.



Technical Datasheet 

AirOS V8.0 

AirOS V7.2 

AirOS V6.0 

AirOS V5.6 

Technical Data:

Manufacturer / Product: Ubiquiti Networks / NanoBeam 5AC-19
Processor Specs: Atheros MIPS 74Kc, 720 MHz
Memory Information: 128MB SDRAM, 8MB Flash
Operating System: AirOS
Networking Interface: 1 x 10/100/1000 BASE-TX (Cat. 5, RJ-45)
Frequency Band: Worldwide: 5150 – 5875 MHz
USA: 5725 – 5850 MHz
Supported Standards: airMAX ac
TX Power: max. 26dBm
RX Sensitivity: min. -96dBm
Range: 15+ km
TCP/IP Throughput: 450Mbps+
Antenna: 19dBi Dual-Linear Backfire Antenna
max. Power Consumption: 8 Watt
Power Method: Passive PoE
24V/0.5A Gigabit PoE Injector is included!
Power Input: 12V – 24V (12 Watt)
ESD/EMP Protection: 24KV radio frequency and ethernet electrostatic discharge (ESD) protection.
Dimensions: 18.9 x 18.9 x 12.5cm
Weight: 0.530 kg
max. Wind Load 45.4 N @ 200 km/h
Operating Temperature: -40°C to +70°C
Operating Humidity: 5 to 95% non-condensing
Shock and Vibration: IEC 68-2-6, IEC 68-2-14


Scope of delivery:

1 x Ubiquiti NanoBeam 5AC-19
1 x 24V/0.5A – Gigabit PoE Injector
1 x Mounting Kit


There are no reviews yet.

Be the first to review “Ubiquiti NANOBEAM NBE-5AC-19”

Your email address will not be published. Required fields are marked *